The upload speed depends on your drive on which the image is stored and is approximately 10-20 minutes.Īt the end of the recovery procedure, Acronis will say that it could not find a driver. It is important not to make a mistake here and indicate the drive to which we are installing Windows. Then we select the target disk for MBR recovery. It is important to check the box here not on the disk itself, but only on the partition and MBR. It is this module that is responsible for decoupling Windows from the hardware on which it was previously installed. Right-click on it and select "Restore".Ĭheck the box “Use Acronis Universal Restore. Our fill will appear in the list of images. We select our USB flash drive and point to the image that we will merge. In the program window, select the "Recovery" item and click the "Search backup". menu item, and then Acronis True Image Premium 2014. As before, select the Linux-utilites Acronis, Paragon. We'll boot from the USB flash drive again by selecting it in the BOOT MENU. Let's check if we did everything right and proceed to the next step - this is the installation of the Windows image 7 using Acronis True Image. Click the finish button and apply the pending operations. We must select the file system NTFS and make sure to make the partition the primary and active one. We do not need the 100 megabyte partition that Windows creates during a standard installation. Even if the section suitable size is, you need to delete it and create a new one. We need to create system partition and make it active. Acronis Disk Director Home will help us with this. menu item.įirst you need to partition your hard drive. Then select the Linux-utilites Acronis, Paragon. In the boot menu, switch to the Grub4dos bootloader. We choose to boot from a USB flash drive. Here is a list of BOOT MENU keys for different hardware manufacturers. This menu is invoked by pressing a certain key immediately after turning on the computer or laptop. Please note that some older boards do not support this mode.īoot from a USB flash drive using the BOOT MENU. This will allow you to use the advanced functions of the hard drive. Now in the 2k10 folder there is a file SetLDR-2k10.exe specially designed for this The third step is uploading the Windows image (installation using Acronis).įirst, set the operating mode hard disk AHCI in your BIOS motherboard. If the size of the flash drive allows, you can copy the Acronis Windows tib images to it.Īttention! In new versions of 2k10 assemblies, the mechanism for recording bootloaders has been slightly changed. Press any button to make the Flash disk bootable.Ĥ. To do this, go to the 2k10 folder on the USB flash drive and run the MakeBoot_XORBOOT.bat file as administrator.ģ. Now you need to connect the bootloader to the USB flash drive. Open the downloaded 2k10 image with Daemon Tools or Winrar and copy all the files to the root of your flash drive.Ģ. Step two - create a multiboot flash drive based on assembly 2k10.ġ. This completes the formatting of the flash drive and it is ready to write files. The last step is to press the "Start" button. In the formatting options, leave only one checkbox "Quick formatting".ĩ. "New volume label" you can write anything you want.Ĩ. In the column “ File system"Specify" NTFS ".ħ. In the second column "Partition scheme and system interface type" select "MBR for computers with BIOS or UEFI."ĥ. In the "Device" column, select your USB flash drive.Ĥ. Insert the USB flash drive into your computer or laptop.ģ. Ask to send you original file again, it may have been damaged in transit ġ.Just replace the word "file" with the name you want Google search example: "File filetype: TIB". You may be lucky enough to find a more suitable version. Try to find the desired file in another source on the Internet.To fix this problem, use one of the recommendations: For example: the file was downloaded incompletely as a result server errors, the file was damaged initially, etc. We also recommend that you check the box next to "Use this app for all tib files".Īnother problem that our users also encounter quite often is that the TIB file is corrupted. As a result, you will see a list installed programs on your computer, and you can choose the right one. To fix this on Windows you need to click right click on file, in context menu hover the mouse over the "Open with" item, and select the "Select program. The most common problem that users cannot open this file is an incorrectly assigned program.
0 Comments
Leave a Reply. |